产 品 承 认 书 目 ½
1、封面---------------------------------1-1
2、目½---------------------------------2-2
3、技术规范-----------------------------3-11
4、产品图纸-----------------------------12-17
1、
SCOPE
适用范围
The contents of specifications for HY series connector strip, including product performance,
test methods and inspection requirements
本规格书内容适用于 HY 系列条½连接器，包含了产品的性½、试验方法和检验要求
2、 APPLICABLE STANDARDS
适用的标准
2.1
GB/T2421
Testing method for Environmental of Electrical Connectors Class 1：
General Principles
GB/T2421
2.2
GB/T2423
GB/T2423
2.3
GB/T2424
GB/T2424
2.4
GB/T5095
电工电子产品环境试验 第一部分 总则
Testing method for Environmental of Electrical Connectors
电工电子产品环境试验方法
Testing method for Environmental of Electrical Connectors
电工电子产品环境试验导则
Testing Procedure/method for components of electric equipment
电子设备用机电元件基本试验规程及测量方法
3、 USE CONDITION
½用条件
3.1
Ambient temperature Range:-25
℃
½+85
℃
环境温度：-25
℃
½+85
℃
3.2
Applicable Wire Sizes:AWG#24½#30
适用线规：AWG#24½#30
3.3
Applicable PC board thickness:0.8~1.6mm
适用
PC
板厚度：0.8~1.6mm
4、 Appearance and Dimension
外观及尺寸
4.1
Appearance:Product surface without defect、dirt、crack、and mechanical damang,
Contact without rust,plating not oxided and not peeled.
产品表面不应有对制品有害的缺陷、污垢、裂痕及机械损伤；接触件无锈蚀、镀层
氧化、脱½等现象.
4.2
Dimension:According to drawings
外½尺寸：依照附图
4.3
Exchangable:Exchangable with same specification products.
互换性：相同规格应½互换
5、Material
材
料
Type
类 型
Contact
插 簧
Plastic
塑 壳
Plastic
塑 壳
Contact
插 针
Plastic
塑 壳
Contact
插 针
Plastic
塑 壳
Wafer
卧贴针座
Contact
插 针
Solder tab
焊护耳
Plastic
塑 壳
Wafer
立贴针座
Contact
插 针
Solder tab
焊护耳
Material
材 料
Phosphor bronze
锡青磷铜 厚
0.20mm
Nylon66
Nylon66
UL94V-0
UL94V-0
Finish
表面处理
Tin Plating:3~5μm
镀锡：3~5μm
Color: White
颜色：½色
Color: White
颜色：½色
Tin Plating:2.5~5μm
镀锡：2.5~5μm
Color: White
颜色：½色
Tin Plating:2.5~5μm
镀锡：2.5~5μm
Color: Beige
颜色：米色
Tin Plating:2.5~5μm
镀锡：2.5~5μm
Tin Plating:3~5μm
镀锡：3~5μm
Color: Beige
颜色：米色
Tin Plating:2.5~5μm
镀锡：2.5~5μm
Tin Plating:3~5μm
镀锡：3~5μm
RoHS
Expiain
说 明
P/N
零件名称
Terminal
端 子
Housing
孔 座
Wafer
直针座
黄铜
Brass
厚□0.50mm
UL94V-0
Wafer
弯针座
Nylon66
黄铜
LCP
Brass
厚□0.50mm
UL94V-0
Brass
厚□0.50mm
Brass
厚
0.40mm
UL94V-0
Brass
厚□0.50mm
黄铜
黄铜
LCP
黄铜
Phosphor bronze
锡青磷铜 厚
0.25mm
6、Electrical Performance
电 气 性 ½
N0.
Ltem
序号
项 目
6.1
6.2
Current Rated
额定电流
Voltage Rated
额定电压
Test mode
试验方法
2A
Requirement
技术要求
AC
DC
DC
250V AC
A maximum voltage of 20mV and a maximum
current of 100mA are applied to the Mate connector
组合状态下的连接器，两端½以最大测试电压
20
mV
以及最大测试电流
100 mA
Does not include wire resistance
不包含电线阻抗
Initial value
Less than
20mΩ
初始值≤20
mΩ
6.3
ContactResistance
接触电阻
N0.
序号
Ltem
项 目
Test mode
试验方法
Apply 1000V AC(rms)for 1 minute and the leakage
current shall not exceed 0.5mA to the adjacent
terminal and ground of the Mate connectors
组合状态下的连接器，相邻两导½末端各½以电
压
1000V AC(有效值)时间 1
分钟，且漏电流必须
小于
0.5mA(毫安培)
Apply 500V DC(rms)for 1 minute between adjacent
contacts to measure the insulation resistance
相邻两接触导½，1 分钟时间内½予
500V DC
电
压，测量期间的绝缘阻抗值
Requirement
技术要求
6.4
withstandvoltage
耐电压
No breakdownor flashover
无击穿或者产生火花
6.5
InsulationResistance
绝缘电阻
More than 1000 MΩ
≥1000MΩ
7、Mechanical Performance:
机 械 性 ½
Ltem
N0.
序号
项 目
Test mode
试验方法
AWG#24 wire
AWG#24
导线
AWG#26 wire
AWG#26
导线
AWG#28 wire
AWG#28
导线
Requirement
技术要求
More than 30N
≥30N
More than 20N
≥20N
More than 13N
≥13N
More than 8N
≥8N
7.1
Terminal crimping
wire strength
端子压接导线强度
Terminal crimping wires, axial
per minute to 25 ± 3mm rate of
the pullout force
端子所压接电线，以每分钟
25±3mm
速率之½向拔出力
AWG#30 wire
AWG#30
导线
7.2
Fixed terminals
and hole seat
端子与孔座固定力
The terminal and the hole seat, at a rate per minute
to 25 ± 3mm along the wire direction are pulled out
from the hole in the seat capacity
Per contact
单一接触点
More than 15N
≥15N
端子与孔座配合，以每分钟
25±3mm
的速率沿导
线方向将端子从孔座中拔出的力
7.3
Singlecontact
insertion force
单接触插入力
The Housing together with the terminal ends with
Wafer matched, at a rate per minute to 25 ± 3mm,
inserting force test
孔座连同端子与针座两端互配，
以每分钟
25±3mm
的速率，½插入力测试
Less than 6N
≤6N
N0.
序号
Ltem
项 目
Test mode
试验方法
The Housing together with the terminal ends with
Wafer matched, at a rate per minute to 25 ± 3mm, as
the pull-out test
孔座连同端子与针座两端互配，
以每分钟
25±3mm
的速率，½拔出力测试
Exerts a force on the pin end, at a rate per minute 25
± 3mm, until the needle exit seat pull-out force
Requirement
技术要求
7.4
Single contact
withdrawal force
单接触拔出力
More than 0.5N
≥0.5N
7.5
Pin Retention
force
PIN
针固定力
Per contact
单一接触点
在针脚前端½加力，以每分钟
25±3mm
的速率，
More than 15N
≥15N
直到针退出针座的拔出力
Mate connectors up 30 cycles at a Maximun rate of
10cycles per minute prior toenvironmental test
7.6
Durability
耐久性
组合状态下的连接器且未经环境测试，每分钟内
进行
10
次嵌入与拔出，连续
30
次嵌入与拔出往
返测试
Connector combination state of the welding circuit
board as test samples, the request in accordance with
the following specifications, resistance to vibration
test, whether to produce discontinuous current
determined
during
the
experiment
(off)
phenomenon, after the experiment measuring
contact resistance
组合状态下的连接器焊接电路板上½为试验样
品，依照如下规格要求，进行耐振动试验，试验
过程中确定是否产生不连续电流（断电）现象，
试验过后测量接触电阻值
Contact Resistance
≤30
mΩ
接触电阻≤30
mΩ
Appearance：No damage
外观：无损伤
7.7
Vibration
振动
Contact Resistance
≤30
mΩ
接触电阻≤30
mΩ
Frequency(频率):10-55-10 Hz/minute
Amplitude(振幅):1.5mm p-p
Direction(方向):
1、Axis of up and down
上下½向(Y ½)
2、Axis of right the left
左右½向(X ½)
3、Axis of front and back
前后½向(Z ½)
Period(周期):2 hous for each direction
每一个½向持续
2
小时
current Discontinuity：
1 micro second Max
电流中断：1μsec
Max
PCB设计
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
