Sunlord
Specifications for Multi-layer Chip Ceramic Inductor
Page 1 of 9
S P E C I F I C AT I O N S
Customer
Product Name
Sunlord Part Number
Customer Part Number
[
New Released,
Revised]
SPEC No.:
SDCL02140000
Multi-layer Chip Ceramic Inductor
SDCL1005 Series
【
This SPEC is total 9 pages including specifications and appendix.
】
【
ROHS Compliant Parts
】
Approved By
Checked By
Issued By
Shenzhen Sunlord Electronics Co., Ltd.
Address: Sunlord Industrial Park, Dafuyuan Industrial Zone, Baoan, Shenzhen, China
518110
Tel: 0086-755-29832660
Fax: 0086-755-82269029
E-Mail: sunlord@sunlordinc.com
【For
Customer approval Only】
Qualification Status:
Full
Approved By
Verified By
Date:
Restricted
Rejected
Checked By
Re-checked By
Comments:
Sunlord
【Version
change history】
Rev.
01
Effective Date
/
Specifications for Multi-layer Chip Ceramic Inductor
Page 2 of 9
Changed Contents
New release
Change Reasons
/
Approved By
Hai Guo
Sunlord
1.
Scope
Specifications for Multi-layer Chip Ceramic Inductor
Page 3 of 9
This specification applies to SDCL1005 series of multi-layer ceramic chip inductor.
2.
Product Description and Identification (Part Number)
1)
2)
Description
SDCL1005 series of multi-layer ceramic chip inductor.
Product Identification (Part Number)
SDCL
①
①
SDCL
※※※※
②
Type
Chip Ceramic Inductor
C
③
XXX
④
□
⑤
◎
⑥
D
⑦
②
F
⑧
External Dimensions (L X W) (mm)
1005 [0402]
1.0 X 0.5
③
Material Code
C
④
Example
3N9
Nominal Inductance
Nominal Value
3.9nH
10nH
100nH
⑤
C
S
H
J
K
⑦
Inductance Tolerance
±0.2nH
±0.3nH
±3%
±5%
±10%
Internal Code
D
⑧
⑥
10N
R10
Packing
T
Tape Carrier Package
HSF Products
Hazardous Substance Free Products
3.
Electrical Characteristics
Please refer to
Appendix A
(Page 9).
1)
2)
Operating and storage temperature range (individual chip without packing): -55
℃
~ +125
℃
Storage temperature range (packaging conditions): -10
℃
~+40
℃
and RH 70% (Max.)
4.
Shape and Dimensions
1)
2)
Dimensions and recommended PCB pattern for reflow soldering: See
Fig.4-1, Fig.4-2
and
Table 4-1.
Structure: See
Fig. 4-3
and
Fig. 4-4.
Chip inductor
C
Solder-resist
Land pattern
B
A
B
Fig. 4-2
Fig. 4-1
[Table 4-1]
Type
1005
[0402]
L
1.0±0.15
[0.039±0.006]
W
0.5±0.15
[0.020±0.006]
T
0.5±0.15
[0.020±0.006]
a
0.25±0.1
[0.010±0.004]
A
0.45~0.55
Unit: mm [inch]
B
0.40~0.50
C
0.45~0.55
Note: The details of different length for different products see
Appendix A:
Electrical Characteristics.
Structure of
Electro-plating
T
Sn
④-2
Ni
Ag
Fig. 4-4
Ceramic
T
①
Ceramic for SDCL Series
②
Internal electrode (Ag)
a
L
a
③
Pull out electrode( Ag)
④-1
Terminal electrode: Inside (Ag)
④-2
Outside (Electro-plating Ni-Sn)
W
④-1
①
②
③
Fig. 4-3
④
Sunlord
3)
Specifications for Multi-layer Chip Ceramic Inductor
[Table 4-2]
Code
①
②
③
④-1
④-2
Part Name
Ceramic Body
Inner Coils
Pull-out Electrode (Ag)
Terminal Electrode: Inside Ag
Electro-Plating: Ni/Sn plating
Material Name
Ceramic Powder
Silver Paste
Silver Paste
Termination Silver Composition
Plating Chemicals
Page 4 of 9
Material Information: See
Table 4-2
4)
The surface with the mark should be on the top side when soldering, but it is not necessary to identify the mark's direction towards left
or right.
5.
Test and Measurement Procedures
5.1 Test Conditions
Unless otherwise specified, the standard atmospheric conditions for measurement/test as:
a.
b.
c.
a.
b.
c.
a.
Ambient Temperature: 20±15℃
Relative Humidity: 65±20%
Air Pressure: 86kPa to 106kPa
Ambient Temperature: 20±2℃
Relative Humidity: 65±5%
Air Pressure: 86kPa to 106kPa
Inspection Equipment: 20× magnifier
If any doubt on the results, measurements/tests should be made within the following limits:
5.2 Visual Examination
5.3 Electrical Test
5.3.1 DC Resistance (DCR)
a.
b.
a.
b.
c.
d.
a.
b.
c.
d.
a.
b.
c.
a.
b.
c.
Refer to
Appendix A.
Test equipment (Analyzer): High Accuracy Milliohmmeter-HP4338B or equivalent.
Refer to
Appendix A.
Test equipment: High Accuracy RF Impedance /Material Analyzer-E4991A+HP16192A,
Test signal: -20dBm or 50mV
Test frequency refers to Appendix A.
Refer to
Appendix A.
Test equipment: High Accuracy RF Impedance /Material Analyzer-E4991A+HP16192A
Test signal: -20dBm or 50mV
Test frequency refers to Appendix A.
Refer to
Appendix A.
Test equipment: High Accuracy RF Impedance /Material Analyzer- E4991A+HP16192A or Agilent E5071C Network
analyzer(when SRF＞3GHz).
Test signal: -20dBm or 50 mV
Refer to
Appendix A.
Test equipment (see
Fig. 5.3.5-1):
Electric Power, Electric current meter, Thermometer.
Measurement method (see
Fig. 5.3.5-1):
1. Set test current to be 0mA.
2. Measure initial temperature of chip surface.
3. Gradually increase voltage and measure chip temperature for corresponding current.
d.
Definition of Rated Current(Ir): Ir is direct electric current as chip surface temperature rose just 20℃
against chip initial surface temperature(Ta) (see
Fig. 5.3.5-2).
Thermometer
Electric Power
Electric
Current
R
Meter
Chip
0
Rated current
Fig. 5.3.5-1
Fig. 5.3.5-2
+20
Ta
Temperature (
℃
)
5.3.5 Rated Current
5.3.2 Inductance (L)
5.3.3 Q Factor (Q)
5.3.4 Self-Resonant Frequency (SRF)
Ir (mA)
Sunlord
5.4 Reliability Test
Items
5.4.1
Terminal
Strength
Specifications for Multi-layer Chip Ceramic Inductor
Page 5 of 9
Requirements
No removal or split of the termination or other
defects shall occur.
Chip
F
②
③
④
Mounting Pad
Glass Epoxy Board
Fig.5.4.1-1
①
①
Test Methods and Remarks
Solder the inductor to the testing jig (glass epoxy board shown
in
Fig. 5.4.1-1)
using leadfree solder. Then apply a force in the
direction of the arrow.
5N force for SDCL1005 series.
Keep time: 10±1s
Speed: 1.0mm/s.
5.4.2
Resistance
Flexure
to
No visible mechanical damage.
Solder the inductor to the test jig (glass epoxy board shown in
Fig. 5.4.2-1)
Using a leadfree solder. Then apply a force in the
direction shown
Fig. 5.4.2-2.
Type
1005[0402]
a
0.4
b
c
Unit: mm [inch]
1.5
0.5
②
③
④
Flexure: 2mm.
Pressurizing Speed: 0.5mm/sec.
Keep time: 30 sec.
20
b
Φ4.5
R230
Flexure
45[1.772]
45[1.772]
Fig. 5.4.2-2
①
②
Solder the inductor to the testing jig (glass epoxy board
The inductor shall be subjected to a simple harmonic
motion
10
c
a
100
Fig. 5.4.2-1
5.4.3
Vibration
①
②
③
No visible mechanical damage.
Inductance change: Within ±10%.
Q factor change: Within ±20%.
Cu pad
Solder mask
40
shown in
Fig. 5.4.3-1)
using leadfree solder.
having total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55 Hz.
③
The frequency range from 10 to 55 Hz and return to 10 Hz shall
be traversed in approximately 1 minute. This motion shall be applied
for a period of 2 hours in each 3mutually perpendicular directions
(total of 6 hours).
Glass Epoxy
Fig. 5.4.3-1
5.4.4 Dropping
①
②
③
5.4.5
Temperature
5.4.6
Solderability
No visible mechanical damage.
Inductance change: Within ±10%.
Q factor change: Within ±20%.
Temperature range: SDCL1005: -55
℃
to +125℃,
Reference temperature: 20℃
①
②
③
④
5.4.7
Resistance to
Soldering Heat
①
②
③
④
No visible mechanical damage.
Wetting shall exceed 95% coverage。.
Inductance change: Within ±10%.
Q factor change: Within ±20%.
①
②
③
④
⑤
Solder temperture:240±2℃
Duration: 3 sec.
Solder: Sn/3.0Ag/0.5Cu.
Flux: 25% Resin and 75% ethanol in weight.
Solder temperature: 260±3℃
Duration: 5 sec.
Solder: Sn/3.0Ag/0.5Cu.
Flux: 25% Resin and 75% ethanol in weight.
The chip shall be stabilized at normal condition for 1~2 hours
before measuring.
5.4.8
Thermal Shock
①
②
③
No mechanical damage.
Inductance change: Within ±10%.
Q factor change: Within ±20%.
30 min.
30 min.
②
③
125℃/85℃
Ambient
Temperature
-55
℃
/-40℃
30 min.
20sec. (max.)
④
①
Temperature, Time: (See
Fig. 5.4.8-1)
-55
℃
for 30±3 min→125
℃
for 30±3min,
Transforming interval: Max. 20 sec.
Tested cycle: 100 cycles.
The chip shall be stabilized at normal condition for 1~2 hours
before measuring.
Drop chip inductor 10 times on a concrete floor from a height of 100
cm.
Inductance change should be within ±10% of
initial value measuring at 20
℃
.
①
②
No visible mechanical damage.
Wetting shall exceed 95% coverage.
Fig. 5.4.8-1
51单片机
京公网安备 11010802033920号
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
