电子工程世界电子工程世界电子工程世界

关键词

搜索

型号

搜索
 

5962-1421013HZX

器件型号:5962-1421013HZX
器件类别:电源/电源管理    电源电路   
厂商名称:Defense Logistics Agency
下载文档

器件描述

DC-DC Regulated Power Supply Module, 1 Output, 20W, Hybrid, PACKAGE-7

参数
参数名称属性值
Objectid8348430525
包装说明,
Reach Compliance Codeunknown
ECCN代码EAR99
模拟集成电路 - 其他类型DC-DC REGULATED POWER SUPPLY MODULE
最大输入电压50 V
最小输入电压16 V
标称输入电压28 V
JESD-30 代码R-XDFM-P7
功能数量1
输出次数1
端子数量7
最高工作温度125 °C
最低工作温度-55 °C
最大输出电压5.15 V
最小输出电压4.85 V
标称输出电压5 V
封装主体材料UNSPECIFIED
封装形状RECTANGULAR
封装形式FLANGE MOUNT
认证状态Qualified
筛选级别MIL-PRF-38534 Class H
表面贴装NO
技术HYBRID
温度等级MILITARY
端子形式PIN/PEG
端子位置DUAL
最大总功率输出20 W
微调/可调输出NO

文档预览

NOT MEASUREMENT
SENSITIVE
MIL-HDBK-103BG
16 OCTOBER 2020
SUPERSEDING
MIL-HDBK-103BF
11 MARCH 2020
DEPARTMENT OF DEFENSE
HANDBOOK
LIST OF STANDARD MICROCIRCUIT DRAWINGS
This handbook is for guidance only. Do not cite this document
as a requirement.
AMSC N/A
DISTRIBUTION STATEMENT A.
Approved for public release.
FSC 5962
Distribution is unlimited.
MIL-HDBK-103BG
FOREWORD
1. This handbook is approved for use by all Departments and Agencies of the Department of Defense.
2. This handbook is for guidance only. This handbook cannot be cited as a requirement. If it is, the contractor does not have
to comply.
3. The proliferation of industry prepared drawings for the same part used in a variety of military applications has become an
ever increasing item of expense to the DoD. Numerous situations have arisen where one military acquisition document would
be more appropriate and cost effective than the multiplicity of contractor prepared drawings. Standard Microcircuit Drawings
(SMDs) are being prepared to eliminate the need for the multitude of contractor prepared drawings for the same device when
the minimum requirements of SMD's are sufficient to meet the requirements of the application on an interim or permanent basis.
4. Comments, suggestions, or questions on this document should be addressed to: Commander, DLA Land and Maritime,
ATTN: VAS, 3990 East Broad St., Columbus, OH 43218-3990, or emailed to
linear@dla.mil.
Since contact information can
change, you may want to verify the currency of this address information using the ASSIST online database at
https://assist.dla.mil.
ii
MIL-HDBK-103BG
CONTENTS
PARAGRAPH
1.
1.1
1.2
1.2.1
1.2.2
1.2.3
1.2.4
2.
3.
4.
4.1
4.2
4.3
4.4
4.5
4.6
5.
5.1
5.2
6.
6.1
6.1.1
6.1.2
6.2
7.
7.1
7.2
TABLE 1
APPENDIX
SECTION 1
Part I
Part II
Part III
Microcircuits ................................................................................................................................... 12
Listed by SMD PIN .....................................................................................................................
12
Listed by generic PIN .................................................................................................................
760
Listed approved sources ............................................................................................................
992
Concluding material ...................................................................................................................
996
PAGE
SCOPE .......................................................................................................................................... 1
Purpose ...................................................................................................................................... 1
Part or identifying number (PIN) ................................................................................................. 1
Drawing number ......................................................................................................................... 1
Device class designator ............................................................................................................. 1
Case outline / lead finish ............................................................................................................ 2
Substitutability ............................................................................................................................ 2
APPLICABLE DOCUMENTS ......................................................................................................... 2
DEFINITIONS ................................................................................................................................ 2
REQUIREMENTS .......................................................................................................................... 2
Drawing requirements ................................................................................................................ 2
Preparation procedures .............................................................................................................. 2
Drawing effectivity and duration ................................................................................................. 2
Approved sources of supply ....................................................................................................... 2
Radiation hardness assurance (RHA) levels .............................................................................. 2
Electrostatic discharge sensitivity (ESD) listing .......................................................................... 3
CONFIGURATION MANAGEMENT .............................................................................................. 3
Configuration management of SMDs ......................................................................................... 3
Record of users .......................................................................................................................... 3
DISTRIBUTION and REQUESTS .................................................................................................. 4
Distribution ................................................................................................................................. 4
Automatic distribution ................................................................................................................. 4
Electronic distribution ................................................................................................................. 4
Requests .................................................................................................................................... 4
NOTES .......................................................................................................................................... 4
Intended use .............................................................................................................................. 4
Subject item (key word) listing .................................................................................................... 4
Noun code descriptions ................................................................................................................. 5
iii
MIL-HDBK-103BG
1. SCOPE
1.1 Purpose. The Standard Microcircuit Drawing Program (SMDP) is directly under the auspices of the
DoD Parts Management Program (PMP). The PMP is implemented by MIL-HDBK-512, "Parts Management." The PMP will be
the avenue for screening candidate parts for the SMDP by the DLA Land and Maritime Military Parts Control Advisory Group
(MPCAG).
1.2 Part or Identifying number (PIN). The PIN's listed in section 1, part I, are composed of the elements shown in the
following example (see 1.2.2 for one part - one part number differentiation):
One part - one part number PIN
5962-90123
Drawing number
(1.2.1)
01
Device
Type
M
Device
Class
Designator
(1.2.2)
X
Case
Outline
(1.2.3)
A
Lead
Finish
(1.2.3)
Non - one part - one part number PIN
86030
or
5962-88668
Drawing number
01
Device type
X
Case outline
(1.2.3)
A
Lead finish
(1.2.3)
1.2.1 Drawing number. One part - one part number SMD's for device classes Q, V, H, and K may cover custom device
products which are generally used to specify application specific integrated circuits (both monolithic and hybrid). To differentiate
between one part - one part number SMD's that cover standard product from custom product a single alpha character will be
placed in the unique 3 digit portion of the SMD drawing number as in the following example: 5962-90A23. This will be the only
change to the SMD PIN for custom products.
1.2.2 Device class designator. One part - one part number SMD's (fully implemented after SMD 5962-90659) contain device
requirements for all three of the major military microcircuit requirements documents. By establishing a one part number system
covering all three documents, the OEM can acquire to the highest level available for a given generic device to meet system
needs without modifying the original contract parts selection criteria.
Military documentation format
New MIL-PRF-38535 Standard
Microcircuit Drawings
New MIL-PRF-38534 Standard
Microcircuit Drawings
New 1.2.1 of MIL-STD-883 Standard
Microcircuit Drawings, based on
Appendix A of MIL-PRF-38535
Example PIN
5962-XXXXXZZ(Q,V,T or N)YY
5962-XXXXXZZ(H,K,D,G or E)YY
5962-XXXXXZZ(M)YY
Manufacturing
source listing
QML-38535
QML-38534
MIL-HDBK-103
Document
listing
MIL-HDBK-103
MIL-HDBK-103
MIL-HDBK-103
This handbook is for guidance only and cannot be cited as a requirement.
1
MIL-HDBK-103BG
1.2.3 Case outline/lead finish. Case outline and lead finish are as described in each SMD. The lead finish indicated in the
section 1 Part I listing is the most readily available from the manufacturer listed for the part. The manufacturer is authorized to
supply other lead finishes than what is listed provided that further testing/qualification is performed by the manufacturer on the
other lead finish(es). The user needs to contact the manufacturer to determine the availability of other lead finishes not listed
herein.
1.2.4 Substitutability. Device-class-Q devices will replace device-class-M devices.
2. APPLICABLE DOCUMENTS This section is not applicable to the handbook.
3. DEFINITIONS This section is not applicable to the handbook.
4. REQUIREMENTS
4.1 Drawing requirements. SMD's will be prepared in accordance with ASME Y14.100 and DOD directives.
4.2 Preparation procedures. The procedures for the generation of an SMD are provided in MIL-HDBK-780.
4.3 Drawing effectivity and duration. SMD's and device class M one part - one part number SMDs which have become
inactive for new design are reflected in section 1, part 1 of the appendix of this document with an "I" in the status column.
4.4 Approved sources of supply. The approved sources of supply list in this handbook supersedes the approved sources
formerly listed in each individual SMD/DLA Land and Maritime Drawing. This handbook is the official list of approved sources of
supply for non-one part - one part number SMD PIN's and for device class M one part - one part number SMD PIN's. Device
classes B, S, Q, V, T, N (monolithic) and H, K, D, G, E (hybrid) one part - one part number SMD PIN's are listed for the
convenience of the users. Official listing for B, S, Q, V, T, N, H, K, D, G, and E levels are available in the applicable QML.
Manufacturers should notify DLA Land and Maritime-VA in writing if they no longer wish to be listed as an approved source of
supply for any device listed herein. This letter will be used by DSCC to remove the manufacturer from MIL-HDBK-103 for those
devices that the manufacturer specifies that he will no longer supply.
4.5 Radiation hardness assurance (RHA) levels. SMD devices which meet the RHA requirements of MIL-PRF-38535 or
MIL-PRF-38534 will be marked with the appropriate RHA designator M, D, P, L, R, F, G, or H replacing the dash (-) in the PIN
as indicated in the following example:
5962(M, D, P, L, R, F, G, or H)8999901EA
Only the highest RHA level for which the device is qualified will be listed in Section 1, Part I of the appendix of this document;
however, at the request of the customer, the manufacturer is authorized to supply any lower RHA level device. At the request of
the customer, the non-RHA PIN designated with a dash (-) may be supplied at the option of the manufacturer. The
manufacturer may also opt to submit a certificate of compliance to have the non-RHA PIN listed in addition to the RHA PIN in
Section 1, Part I of the appendix of this document.
2
【新思科技IP资源】用于高性能计算 SoC 的整体以太网 PHY IP 剖析
简介 随着系统需求的增加,超大规模数据中心需要适时扩展。对于超大规模数据中心所需的服务器到服务器通...
arui1999 综合技术交流
请教大虾?
刚接触430编程,请问以下语句的作用?能详尽点最好,谢谢! do { IFG1 &=...
lph1025 微控制器 MCU
一个很搞的程序,运行结果非常意外,苦思无果
这几天一个同学做了个单片机的小程序,非常简单的功能,就是驱动数码管显示。但是他用了两个74HC573...
zhfzhyue 单片机
MicroPython动手做(24)——掌控板之拓展掌控宝
掌控拓展板(parrot)是掌控板衍生的一款体积小巧、易于携带的拓展板。支持电机驱动、语音播放、语音...
eagler8 MicroPython开源版块
周立功和华为哪个待遇好?
周立功和华为哪个待遇好? 周立功和华为哪个待遇好? ...
毛承玲 PCB设计
AD原理图分图后怎么跟PCB保持同步?
一开始画图时花了两个原理图,画完PCB以后看着原理图有点乱,所以根据功能把原理图多分了几个,但是发现...
liyancao001 PCB设计

About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版

站点相关: 大学堂 TI培训 Datasheet 电子工程

器件索引   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

北京市海淀区知春路23号集成电路设计园量子银座1305 电话:(010)82350740 邮编:100191

电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2022 EEWORLD.com.cn, Inc. All rights reserved