电子工程世界电子工程世界电子工程世界

关键词

搜索

型号

搜索
 

MAX2204_1

器件型号:MAX2204_1
厂商名称:Maxim(美信半导体)
厂商官网:https://www.maximintegrated.com/en.html
下载文档

器件描述

Evaluation Kit

文档预览

19-0779; Rev 0; 3/07
MAX2204 Evaluation Kit
General Description
The MAX2204 evaluation kit (EV kit) simplifies evalua-
tion of the MAX2204 RF power detector. The EV kit
enables testing of all functions with no additional sup-
port circuitry. The RF power-detector input uses a 50Ω
SMA connector on the evaluation board for convenient
connection to test equipment.
o
50Ω SMA RF Input Port Connector
o
Fully Assembled and Tested
Features
o
+2.7V to +3.3V Single-Supply Operation
Evaluates: MAX2204
Ordering Information
PART
MAX2204EVKIT+
TEMP RANGE
-40°C to +85°C
IC PACKAGE
5 SC70
+Denotes
a lead-free and RoHS-compliant EV kit.
Component List
DESIGNATION
C1
C2
C3
C4
J1, J2
QTY
1
1
1
1
2
DESCRIPTION
220pF ±10% capacitor (0402)
Murata GRM155R71H221K
27pF ±5% capacitor (0402)
Murata GRM155R71H270J
22µF ±10% capacitor (1206)
Murata GRM31CR60J226K
2200pF ±10% capacitor (0402)
Murata GRM155R71H222K
Inline headers
Sullins PEC36SAAN
SMA end-launch jack receptacle,
0.062in
Johnson 142-0701-801
2-pin jumper block, single
Digi-Key S1012-36-ND
Test point, PC mini, red
Keystone 5000
50Ω ±5% resistor (0402)
0Ω ±5% resistor (0402)
MAX2204EXK+ RF Power Detector
PCB: MAX2204 Evaluation Kit+
Quick Start
Test Equipment Required
This section lists the
recommended
test equipment to
verify operation of the MAX2204. It is intended as a
guide only, and some substitutions are possible:
• One RF signal generator capable of delivering at
least +5dBm of output power at the operating
frequency (HPE4433B or equivalent)
One RF power sensor capable of handling at least
+10dBm of output power at the operating
frequen-
cy (HP 8482A or equivalent)
One RF power meter capable of measuring up to
+10dBm of output power at the operating frequen-
cy (HP 437B or equivalent)
An RF spectrum analyzer that covers the MAX2204
operating frequency range (e.g., FSEB20)
A power supply capable of up to 10mA at +2.7V to
+3.3V
A digital multimeter (DMM) for measuring output
voltage, supply current, and output current
50Ω SMA cables
A network analyzer (e.g., HP 8753D) to measure
input impedance (optional)
J4
1
JP1
JP3
R1
R2
U1
1
1
1
1
1
1
Component Suppliers
SUPPLIER
Johnson Components
Murata Mfg. Co., Ltd.
PHONE
507-833-8822
770-436-1300
WEBSITE
www.johnsoncomponents.com
www.murata.com
Note:
Indicate that you are using the MAX2204 when contacting these component suppliers.
________________________________________________________________
Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
MAX2204 Evaluation Kit
Evaluates: MAX2204
Connections and Setup
This section provides a step-by-step guide to operating
the EV kit and testing the device’s function.
Caution:
Do not turn on the DC power or RF signal genera-
tors until all connections are made:
1) Set the jumper (JP1) on the EV kit to ON. This
enables the device.
2) Connect a DC supply set to +2.85V (through a
DMM, if desired) to the VCC and GND terminals on
the EV kit. If available, set the current limit to 10mA.
Do not turn on the supply.
3) Connect the output (J3) to a DMM to measure output
voltage.
4) Set the signal generator output to +5dBm,
f = 836MHz. Using the power meter, determine the
actual output power of the signal generator.
5) Connect the signal generator to the SMA connector.
Do not turn on the signal generator.
6) Turn on the DC supply; the supply current should
read approximately 1.3mA.
7) Activate the signal generator. The output voltage
should read approximately 2V.
Layout Issues
The MAX2204 is not particularly sensitive to the layout,
since it only needs 5dBm for maximum output voltage.
However, there are two areas that need attention: the
GND pin and the supply bypassing. Connect the GND
pin to PCB ground with a GND via as close as possible,
and place the supply bypassing capacitor close to the
part.
C2
27pF
VCC
J1
VCC
1
2
R2
0Ω
OUT
JP3
C4
2200pF
4
VCC
1
2
JP1
3
V
CC
OUT
GND
U1
MAX2204
5
J2
C3
22µF
J4
C1
220pF
3
R1
50Ω
ENA
RFIN
Figure 1. MAX2204 EV Kit Schematic
2
_______________________________________________________________________________________
MAX2204 Evaluation Kit
Evaluates: MAX2204
1.0"
1.0"
Figure 2. MAX2204 EV Kit Component Placement Guide—Top
Silkscreen
Figure 3. MAX2204 EV Kit Component Placement Guide—
Component Side
1.0"
Figure 4. MAX2204 EV Kit Component Placement Guide—
Secondary/Bottom Component Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 _____________________
3
© 2007 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
Janet Freed

技术资料推荐

论坛推荐

技术视频推荐

About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版

站点相关: 大学堂 TI培训 Datasheet 电子工程

器件索引   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
搜索索引   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
器件入口   0A 65 7S AN EC KK MZ QN S9 SH VM WS WY X7 ZE

北京市海淀区知春路23号集成电路设计园量子银座1305 电话:(010)82350740 邮编:100191

电子工程世界版权所有 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号 Copyright © 2005-2021 EEWORLD.com.cn, Inc. All rights reserved