电子工程世界电子工程世界电子工程世界

产品描述

搜索
 

HWW-X072T-065070-H1

器件型号:HWW-X072T-065070-H1
厂商名称:P-tec
厂商官网:http://www.p-tec.net/
下载文档

器件描述

X72T RGB LED WALL WASHERS

HWW-X072T-065070-H1器件文档内容

Page 1 of 5

ATG Electronics SmartTM X72T RGB LED Wall Washer

USER GUIDE

Part Number  HWW-X072T-065070-H1
             HWW-X072T-065070-H2

NOTE:
The purpose of this user guide is to explain the necessary steps for use of SmartTM X72T, and to assure
peak performance of said product. It is intended for use as reference by a fully qualified electrician or
technician. This document should never be considered a substitute for any provision of a regulation or
state or local code.
Please read this entire manual to fully understand and safely use this product.
Specifications are subject to change without notice. Please visit www.atgelectronics.com for the most
recent user guide versions.

GETTING STARTED

This guide contains important information about installing and operating your new SmartTM X72T safely
and properly.

Included in this Box
SmartTM X72T RGB LED Wall Washer, 1 PCs
User Guide, 1 Set

Additional Items Needed
Control System: DynColorTM 500-SL RGB DMX Controller
Signal Amplifier: MasterTM 192-SA Signal Amplifier

Unpacking
1) Unpack and carefully examine the product.
2) Report any damage and save all packing materials if any part of the apparatus was damaged durin g
shipping.
3) Do not attempt to use this apparatus if it is damaged.

Cautions
1) W arning: Risk of electric shock! Ensure that the power supply is off when wiring or soldering the device
during installation.
2) The device should be installed and operated by a qualified electrician or technician in accordance with
relevant local codes.
3) Do not use sharp tools near or on the surface of the device.
4) Suggested continuous working time is around 8 hours. Never use for more than 12 consecutive hours.

                                                                                         ATG
                                                                                              Electronics Corp.

                                                                                         Light your world
                                                                                                Color your life!
Page 2 of 5

User Responsibilities
The responsibility of complying with all state and local laws, ordinances, and regulations in regards to the
installation, maintenance, and operation of the device lies with the buyer and handler of the device.
These parties may include, but are not limited to the contractor, installer, purchaser, owner, and user of
the product.

Note:
The instructions and precautions set forth in this user guide are not necessarily inclusive of or relevant to
all applications as ATG Electronics cannot anticipate all possible situations.

PLANNING THE INSTALLATION

This device installation requires planning to ensure timely installation with minimal complications and
down time.

Planning Suggestions
Consult an electrical inspector when reviewing all wiring plans.
Create a layout plan blueprint, per a lighting designer's or architect's recommendations.
Consult ATG Electronics's Application Engineering Services as needed.

Installation Considerations
When creating your installation plan, consider the following:
1) Location of the device
SmartTM X72T is suitable for only dry, wet and damp environments.
2) Control System
SmartTM X72T can be controlled by DynColorTM 500-SL RGB DMX Controller. Synchronous color
changing might be considered before installing.
3) Lighting Distance
The maximum lighting distance for SmartTM X72T is around 20 meters (65 feet).
4) Maximum Series-wound Length
100 meters (328 feet). MasterTM 192-SA Signal Amplifier is needed at every 100 meters (328 feet).

Installation Steps
1) Place SmartTM X72T at the required locations and aim them according to your lighting design.
2) Adjust the rotary angle to required angle.
3) Connect SmartTM X72T to each other. Signal Amplifiers are needed every 100 meters or 328 feet.

                                                                                               www.atgelectronics.com
Page 3 of 5
4) Finish waterproof treatment at every signal connector joint. (Please refer to picture below).

5) Connect the DMX Console to the first SmartTM X72T.
6) Plug the first SmartTM X72T and DMX console into power outlets to power the system.

Operation Instruction

1) Buttons Functions

Button                 Control Mode             Function                                Example

                       DMX-Control    Displays the DMX address selected
                                      (valid DMX addresses from 001~512)

                                      Displays the color-changing mode and

                       Self-Control speed selected (P=self-control, X=mode,

                                      Y=speed)

                       DMX-Control Select a parameter for configuration                           -

                       Self-Control Select mode or speed for configuration                        -

                       DMX-Control Set corresponding parameter                                    -

                       Self-Control Set corresponding mode/speed                                  -

2) How to change settings in DMX-Control mode

A. Once the wall washer is connected to the DMX console, it will access DMX-Control mode.

B. Press button "A" to select a parameter for the DMX address.

C. Press button "B" to change the DMX address.

D. Valid DMX address range: 001~512. (Refer to the user guide of the DMX Console for more detailed

information on operating the DMX Console.)

E. Each wall washer occupies three DMX channels, including red, green, and blue. For example, the wall

washer at DMX address 001 occupies channels 1, 2, and 3; the wall washer at DMX address 256

occupies channels 256, 257, and 258.

3) How to access and set under Self-Control mode
A. Press button "A" four times. This will access Self-Control mode and the letters "PXY" will be displayed.

                                                                                                  www.atgelectronics.com
Page 4 of 5

B. Press button "A" once. The digital LED should start to flash and you will be given access to the
corresponding setup (mode).
C. Press button "B" to change the corresponding setup (speed or brightness). The digital LED should
display values 1 through 9.

D. Master/Slave Mode:
Choose one wall washer as the master and set its DMX address to 001.
Choose other wall washers as slaves and assign them any DMX addresses except 001.
Press button "A" of the master wall washer four times to access Self-Control mode.
Change the mode of the master wall washer. All slave wall washers will work synchronously with the
master.

E. Parameter form of "PXY"

P               X (mode)                           Y (speed/brightness)
                                          9 brightness levels, (brightest at 9)
-               1 (Static Red)            9 brightness levels, (brightest at 9)
                                          9 brightness levels, (brightest at 9)
-               2 (Static Green)          9 brightness levels, (brightest at 9)
                                          9 brightness levels, (brightest at 9)
-               3 (Static Yellow)         9 brightness levels, (brightest at 9)
                                          9 brightness levels, (brightest at 9)
-               4 (Static Blue)
                                              9 speed levels, (fastest at 9)
-               5 (Static Pink)               9 speed levels, (fastest at 9)
                                              9 speed levels, (fastest at 9)
-               6 (Static Cyan)

-               7 (Static White)

-               8 (Multi-color jumping)

-               9 (Multi-color fading)

-               A (Multi-color flashing)

4) How to exit the selected mode?
Press a button of your choosing and wait for around 10 seconds for the device to exit from selected mode.
The digital LED will stop flashing and the wall washer will retain the currently the selected mode and
parameter.

Wiring Diagram

                                                                                 www.atgelectronics.com
Page 5 of 5

                                  Max 100m(328ft) in series connection

ATG Electronics SmartTM X72T RGB LED Wall Washer Specifications
Input Voltage: 120 VAC/240 VAC
Color: RGB
LED Qty: 72 LEDs
Lumens (single LED): 44 lm/W (Red), 70 lm/W (Green), 15 lm/W (Blue)
Power Consumption: 110 W (Max.)
Beam Angle: 15
Dimension: L636 * W150 * H172 mm (L25.04 * W5.9 * 6.77 inches)

IP Rating: IP65 (applicable for dry, wet, damp environments)
* For detailed specifications please refer to the product catalog of SmartTM X72T RGB LED Wall Washer.

628 Zhangyang Road, Suite 1-21B                                         ATG
Shanghai 200122, CHINA                                                     Electronics Corp.
www.atgelectronics.com
E-mail: sales@atgelectronics.com                                        Light your world
Phone: +86-21-58350166                                                        Color your life!
Fax: +86-21-58351977

Ver5.3-120420
This datasheet has been downloaded from:
            datasheet.eeworld.com.cn

                 Free Download
           Daily Updated Database
      100% Free Datasheet Search Site
  100% Free IC Replacement Search Site
     Convenient Electronic Dictionary

               Fast Search System
             www.EEworld.com.cn

                                                 All Datasheets Cannot Be Modified Without Permission
                                                                Copyright Each Manufacturing Company
小广播

About Us 关于我们 客户服务 联系方式 器件索引 网站地图 最新更新 手机版

站点相关: 大学堂 TI培训 Datasheet 电子工程

北京市海淀区知春路23号集成电路设计园量子银座1305 电话:(010)82350740 邮编:100191

电子工程世界版权所有 京ICP证060456号 京ICP备10001474号 电信业务审批[2006]字第258号函 京公海网安备110108001534 Copyright © 2005-2020 EEWORLD.com.cn, Inc. All rights reserved