APL1117
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed
1.8V, 2.5V, 2.85V and 3.3V
Features General Description
Guaranteed Output Voltage Accuracy within 2% The APL1117 is a low dropout three-terminal adjust-
able regulators with 1A output current capability. In
Fast Transient Response
order to obtain lower dropout voltage and faster tran-
Guaranteed Dropout Voltage at Multiple sient response, which is critical for low voltage ap-
plications , the APL1117 has been optimized. The
Currents device is available in an adjustable version and fixed
Load Regulation : 0.1% Typ. output voltages of 1.8V, 2.5V, 2.85V and 3.3V. The
Line Regulation : 0.03% Typ. output available voltage range of an adjustable ver-
sion is from 1.25~10.7V with an input supply below
Low Dropout Voltage : 1.1V Typ. at IOUT =1A 12V. Dropout voltage is guaranteed at a maximum of
Current Limit : 1A Typ. at TJ=25C 1.3V at 1A. Current limit is trimmed to ensure speci-
fied output current and controlled short-circuit current.
On-Chip Thermal Limiting : 150C Typ. On-chip thermal limiting provides protection against
Adjustable Output : 1.25~10.7V any combination of overload that would create exces-
sive junction temperatures. The APL1117 is available
Standard 3-pin TO-220, TO-252, TO-263 and in the industry standard 3-pin TO-220, TO-252, TO-
263, and the low profile surface mount SOT-223
SOT-223 Power Packages power packages which can be used in applications
where space is limited.
Applications Pin Description
Active SCSI Terminators Front View for TO-220
Low Voltage Logic Supplies
Battery-Powered Circuitry 3 V IN
Post Regulator for Switching Power Supply
2 V OUT
1 ADJ/GND
Front View for TO-263
3 VIN
TAB is VOUT 2 V
OUT
1 ADJ/GND
Front View for TO-252
3 V
IN
TAB IS V 2 V OUT
OUT
1 ADJ/GND
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise
customers to obtain the latest version of relevant information to verify before placing orders.
Copyright ANPEC Electronics Corp. 1 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Pin Description (Cont.)
Front View for SOT-223
3 IN
T A B IS V O U T 2 OUT
1 A D J/G N D
Ordering and Marking Information
APL1117- Package Code
F : TO -220 G : TO -263 U : TO -252 V : S O T-223
33 : 3.3V
Temp. Range
H a ndling C ode C : 0 to 70 C
Temp. Range
Package Code H a ndling C ode
V oltage C ode
TU : Tube TR : Tape & Reel
V oltage C ode
18 : 1.8V 25 : 2.5V 28 : 2.85V
B lank : A djusta ble V ersion
AP L1117 F/G /U : APL1117 X X X X X - D ate C ode APL1117 V : APL1117 XX XXX - Date Code
XXXXX XXXXX
18 X X X X X - D ate C ode AP L1117-18V : APL1117 XX XXX - Date Code
A P L1117-18F /G /U : A P L1117 XXXXX18
XXXXX
25 X X X X X - D ate C ode AP L1117-25V : APL1117 XX XXX - Date Code
A P L1117-25F /G /U : A P L1117 XXXXX25
XXXXX
28 X X X X X - D ate C ode AP L1117-28V : APL1117 XX XXX - Date Code
A P L1117-28F /G /U : A P L1117 XXXXX28
XXXXX
33 X X X X X - D ate C ode AP L1117-33V : APL1117 XX XXX - Date Code
AP L1117 -33F/G /U : AP L1117 XXXXX33
XXXXX
Absolute Maximum Ratings
Symbol Parameter Rating(Note) Unit
VI 15 V
TJ Input Voltage APL1117, APL1117-33 9 C
TSTG APL1117-18, APL1117-25, APL1117-28 0 to 125 C
TL 0 to 150 C
Operating Junction Temperature Range -65 to +150
Control Section 260
Power Transistor
Storage Temperature Range
Lead Temperature (Soldering, 10 second)
Note : The values here show the absolute maximum rating, and for normal usage please refer the test condition in Electrical
Characteristics Table.
Copyright ANPEC Electronics Corp. 2 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Electrical Characteristics (Cont.)
Symbol Parameter Test Conditions APL1117 Unit
Min. Typ. Max.
VREF Reference Voltage 10mA IOUT 1A, 1.4V(VIN -VOUT) 10.75V, 1.225 1.250 1.275 V
TJ =0~125C
VOUT Output Voltage
APL1117-18 TJ =0~125C, 1.764 1.800 1.836
0 IOUT 1.5A, 3.5VVIN9V,
APL1117-25 TJ =0~125C, 2.450 2.500 2.550
0 IOUT 1A, 4VVIN9V, V
APL1117-28 TJ =0~125C, 2.790 2.850 2.910
0 IOUT1A, 4.25VVIN9V,
APL1117-33 TJ =0~125C, 3.235 3.300 3.365
0 IOUT 1A, 4.75VVIN12V,
REGLINE Line Regulation 0.03 0.2 %
APL1117 IOUT=10mA, 1.5V(VIN -VOUT )10.75V (Note1) 1 6 mV
16
APL1117-18 IOUT=0A, 3.5VVIN9V (Note1) 16
APL1117-25 IOUT=0A, 4VVIN5.5V (Note1) 16
APL1117-28 IOUT=0A, 4.25VVIN 5.15V (Note1)
APL1117-33 IOUT=0A, 4.75VVIN 7.75V (Note1)
REGLOAD Load Regulation 0.1 0.4 %
APL1117 (VIN -V = OUT) 3V, 0 IOUT 1A (Note1) 1 10 mV
1 10
APL1117-18 VIN=3.5V, 0 IOUT 1A (Note1) 1 10
APL1117-25 VIN =4V, 0 IOUT 1A (Note1) 1 10
APL1117-28 VIN=4.25V, 0 IOUT 1A (Note1)
APL1117-33 VIN=4.75V, 0 IOUT 1A (Note1) 1 1.1
1.05 1.2 V
VD Dropout Voltage IOUT=100mA (Note2) 1.1 1.3
IOUT=500mA (Note2)
IOUT=1A (Note2)
ILIMIT Current Limit (VIN -V ) OUT =5V, TJ=25C 1000 mA
IADJ Adjust Pin Current (VIN -V = OUT) 3V, IOUT=10mA 60 120 A
APL1117
IADJ Adjust Pin Current 10mA IOUT 1A, 0.2 5 A
IO
Change APL1117 1.4V(VIN -VOUT) 10.75V
Minimum Load (VIN -V ) OUT =10.75V (Note3) 1.7 mA
Current APL1117
PSRR Ripple Rejection fRIPPLE=120Hz, VRIPPLE=1VP-P, 60 75 dB
TR (VIN -V = OUT) 3V
0.01 0.02 %/ W
Thermal Regulation TJ=25C, 30ms Pulse
TS Temperature 0.5 %
Stability
LS Long -Term TJ =125C,1000Hrs. 0.3 %
Stability
Copyright ANPEC Electronics Corp. 3 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Electrical Characteristics (Cont.)
Symbol Parameter Test Conditions APL1117 Unit
Min. Typ. Max.
VN RMS Output Noise TJ=25C,10HzF10kHz, (% of VOUT) 0.003 %
th Thermal Resistance Junction to Case, at Tab 15 C/ W
Junction to Ambient
50
OT Over Temperature
Point 150 C
IQ Quiescent Current 5.5 10 mA
APL1117-18 VIN9V 5.5 10
APL1117-25 VIN9V 5.5 10
APL1117-28 VIN9V 5.5 10
APL1117-33 VIN12V
Note 1 : See thermal regulation specifications for changes in output voltage due to heating effects. Load line regulations are mea-
sured at a constant junction temperature by low duty cycle pulse testing.
Note 2 : Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the minimum input/output
differential measured at the specified output current. Test points and limits are also shown on the Dropout Voltage curve.
Note 3 : Minimum load current is defined as the minimum output current required to maintain regulation.
Copyright ANPEC Electronics Corp. 4 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Application Circuits Improving Ripple Rejection
1.25V to 10.7V Adjustable Regulator
APL1117 APL1117
VIN IN OUT VOUT1 V IN IN OUT VOUT
150 F
ADJ R1 + 100F + ADJ R1
C2 10F 121
121 1%
+ 10F + C1
10F
C1* R2 R2
365
1k 1%
* Needed if device is far from filter capacitors * C1 improves ripple rejection.
R1 + R2 XC should be approximately
equal to R1 at ripple frequency
VOUT = 1.250V X R1
5V Regulator with Shutdown
APL1117
VIN IN OUT 5V
100 F
+ ADJ 121
10 F 1%
1k +
TTL
365
1k 1%
Copyright ANPEC Electronics Corp. 5 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Typical Characteristics
Load Transietn Response Line Transient Response
5 APL1117-33 0.02 6 APL1117-33 0.15
4.5
0.01 5
4
Output Current (A) 3.5 0 Input Voltage (V) 4 0.1
-0.01 0.05
3 -0.02 CIN=10F
2.5 COUT=10F Tantalum
IOUT=0.1A
2 CIN=10F 3
1.5 COUT=10F Tantalum
VIN=5V 2
1 0
0.5
1
0
-100 -0.03 0 -0.05
100 300 500 700 900
-20 30 80 130 180
Time (S)
Time (S)
Dropout Voltage vs. Output Current Output Voltage vs. Input Voltage
1.25 APL1117-33 3.5
3
1.2
2.5
Dropout Voltage (V) 1.15 Output Voltage (V) 2
1.1 1.5
1
1.05
0.5
1 0
0 12 3 45 6 78 9
0.95
Input Voltage (V)
0.9
0 0.2 0.4 0.6 0.8 1
Output Current (A)
Copyright ANPEC Electronics Corp. 6 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Typical Characteristics Cont.
Input Current vs. Input Voltage Current Limit vs. Input Voltage
6 APL1117-33 APL1117-33
2.4
5 2.2
Input Current (mA) Current Limit (A) 2
4
1.8
3
1.6
2
1.4
1 1.2
0 1
0 2 4 6 8 10 12 5 7 9 11 13
Input Voltage (V) Input Voltage (V)
Output Voltage vs. Temperature Output Voltage vs. Temperature
2.6 3.4
2.5
2.4 3.3
Output Voltage (V) 2.3 Output Voltage (V) 3.2
2.2
2.1 3.1
2 3
1.9
2.9
1.8
1.7 2.8
1.6 2.7
-50 -25
-50 -25 0 25 50 75 100 125 0 25 50 75 100 125
Temperature (C) Temperature (C)
Copyright ANPEC Electronics Corp. 7 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Typical Characteristics Cont.
Adjustable Pin Current vs. Temperature Input Current vs. Tmeperature
APL1117-Adj 8 APL1117-33
70
Adjustable Pin Current (A) 68
66 7
64 Input Current (mA) 6
62
60 5
58
56 4
54 3
52
50 0 25 50 75 100 125 2 0 25 50 75 100 125
-50 -25 -50 -25
Temperature (C) Temperature (C)
Current Limit vs. Temperature PSRR vs. Frequency
APL1117-33 +0 Cadj=22F APL1117-33
-10 IOUT=0.1A
1.9
Vripple=1Vp-p
1.8 -20
Current Limit (A) 1.7 -30
VIN-VOUT=5V
1.6
PSRR (dB) -40
1.5
-50
1.4 -60
VIN-VOUT>=Vdropout
1.3 -70
1.2 -80
1.1 -90 VIN-VOUT>=3V
5k 10k 20k 50k 200k
1 -100
10 20
-50 0 50 100 150 50 100 200 500 1k 2k
Temperature (C) Frequency (Hz)
Copyright ANPEC Electronics Corp. 8 www.anpec.com.tw
Rev. B.$8 - Jun., 2003
APL1117
Application Information
Output Voltage Rp
The APL1117 develops a 1.25V reference voltage P A R A S IT IC
between the output and the adjust terminal. By plac-
ing a resistor between these two terminals, a con- APL1117 LINE RESISTANCE
stant Current is caused to flow through R1 and down
through R2 to set the overall output voltage. Normally V IN OUT
this current is chosen to be the specified minimum IN
load current of 10mA. For fixed voltage devices R1
and R2 are included in the device. ADJ
R1 RL
CONNECT
R1 TO CASE
R2
APL1117 CONNECT
R2 TO LOAD
V IN IN OUT VOUT
R1 Figure 2. Connections for Best Load Regulation
ADJ VREF
R2 Input Capacitor
IADJ
60 A An input capacitor of 10F or greater is
recommended. Tantalum, or aluminum electrolytic
VOUT = VREF(1+ RR21)+IADJR2 capacitors can be used for bypassing. Larger Val-
ues will improve ripple rejection by bypassing the in-
Figure 1. Basic Adjustable Regulator put to the regulator.
Load Regulation
When the adjustable regulator is used. Load regula- Output Capacitor
tion will be limited by the resistance of the wire con-
necting the regulator to the load. The data sheet speci- The APL1117 requires an output capacitor to main-
fication for load regulation is measured at the output tain stability and improve transient response. Proper
pin of the device. Best load regulation is obtained capacitor selection is important to ensure proper
when the top of the resistor divider (R1) is tied di- operation. The APL1117 output capacitor selection
rectly to the output pin of the device, not to the load. is dependent upon the ESR (equivalent series
For fixed voltage devices the top of R1 is internally resistance) of the output capacitor to maintain stability.
connected to the output, and the ground pin can be When the output capacitor is 10uF or greater, the
connected to low side of the load. If R1 were con- output capacitor should have an ESR less than 1.
nected to the load, RP is multiplied by the divider This will improve transient response as well as pro-
ratio, the effective resistance between the regulator mote stability. A low-ESR solid tantalum capacitor
and the load would be: works extremely well and provides good transient re-
Rp X (1+ RR21), Rp = Parasitic Line Resistance sponse and stability over temperature.
Copyright ANPEC Electronics Corp. 9 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Application Information (Cont.)
Output Capacitor (Cont.) Figure 3&4 shows for the TO-252 and SOT-223 the
Aluminum electrolytics can also be used, as long as measured values of (J-A) for different copper area
the ESR of the capacitor is <1. The value of the
output capacitor can be increased without limit. Higher sizes using a 2 layers, 1.6mm, and 6Sq. cm FR-4
capacitance values help to improve transient response PCB with 2oz. copper and a ground plane layer on
and ripple rejection and reduce output noise. the backside area used for heatsinking. It can be
used as a rough guideline in estimating thermal
Ripple Rejection resistance.
The curves for Ripple Rejection were generated us- 50
ing an adjustable device with the adjust pin bypassed. TA=25C
With a 22F bypassing capacitor 75dB ripple rejec-
tion is obtainable at any output level. The impedance 45
of the adjust pin capacitor, at the ripple frequency, Thermal Resistance
should be < R1. R1 is normally in the range of 100- (Juntion to Ambient) (C/W) 40
200. The size of the required adjust pin capacitor
is a function of the input ripple frequency. At 120Hz, 35
with R1=100, the adjust pin capacitor should be
13F. For fixed voltage devices, and adjustable de- 30
vices without an adjust pin capacitor, the output ripple
will increase as the ratio of the output voltage to the 25
reference voltage (VOUT /VREF ).
0 2 4 6 8 10 12 14
Top Copper Area (cm2)
Figure 3.
(J-A) vs. copper area for the SOT-252 package
Thermal Considerations
APL1117 has thermal protection which limits junction
temperature to 150C. However, device functionality
is only guaranteed to a maximum junction tempera-
ture of +125C.
Both the TO-220, TO-252, TO-263 and SOT-223
packages use a copper plane on the PCB and the
PCB itself as a heatsink. To optimize the heat sinking
ability of the plane and PCB, solder the tab of the
package to the plane.
Copyright ANPEC Electronics Corp. 10 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Application Information (Cont.)
Thermal Considerations (Cont.)
Thermal Resistance 60
(Juntion to Ambient) (C/W) TA=25C
55
50
45
40
35
30
0 2 4 6 8 10 12 14
Top Copper Area (cm2)
Figure 4.
(J-A) vs. copper area for the SOT-223 package
The thermal resistance for each application will be
affected by thermal interactions with other compo-
nents on the board. Some experimentation will be
necessary to determine the actual value.
The power dissipation of APL1117 is equal to :
PD = (VIN - VOUT) x IOUT
Maximum junction temperature is equal to :
TJUNCTION = TAMBIENT + (PD x JA)
Note: TJUNCTION must not exceed 125C
Copyright ANPEC Electronics Corp. 11 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117 R
Package Information be
b1 e1
TO-220 ( Reference JEDEC Registration TO-220)
D
Q
E
L1
H1 L
A c J1
F
M illim ete rs Inches
Dim Min. Max. Min. Max.
0.140 0.190
A 3.56 4.83 0.045 0.070
0.020 0.045
b1 1.14 1.78 0.012 0.045
0.560 0.650
b 0.51 1.14
0.090 0.110
c 0.31 1.14 0.190 0.210
0.380 0.420
D 14.23 16.51 0.020 0.055
0.230 0.270
e 2.29 2.79 0.080 0.115
0.500 0.580
e1 4.83 5.33 0.143 0.250
0.139 0.161
E 9.65 10.67 0.100 0.135
F 0.51 1.40
H1 5.84 6.86
J1 2.03 2.92
L 12.7 14.73
L1 3.65 6.35
R 3.53 4.09
Q 2.54 3.43
Copyright ANPEC Electronics Corp. 12 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117 A
C1
Package Informaion
TO-252( Reference JEDEC Registration TO-252)
E
b2
L2
b D
H
e1
D1 L1
L
C
A1
E1
Dim Millimeters Inches
A Min. Max. Min. Max.
A1
b 2.18 2.39 0.086 0.094
b2
C 0.89 1.27 0.035 0.050
C1
D 0.508 0.89 0.020 0.035
D1
E 5.207 5.461 0.205 0.215
E1
e1 0.46 0.58 0.018 0.023
H
L 0.46 0.58 0.018 0.023
L1
L2 5.334 6.22 0.210 0.245
5.2 REF 0.205 REF
6.35 6.73 0.250 0.265
5.3 REF 0.209 REF
3.96 5.18 0.156 0.204
9.398 10.41 0.370 0.410
0.51 0.020
0.64 1.02 0.025 0.040
0.89 2.032 0.035 0.080
Copyright ANPEC Electronics Corp. 13 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Package Information
TO-263 ( Reference JEDEC Registration TO-263)
E TERMINAL 4
L2 E1
D D1
L
L3
e b2
b
e1
A
c2
1 R
L4 L1
DETAIL "A"ROTED
c
Dim Min. Millimeters Max. Min. Inches Max.
4.06 0.38 TYP. 4.83 0.160 0.015 TYP. 0.190
A 0.51 2.54 TYP 1.016 0.02 0.100 TYP 0.040
b 1.14 1.651 0.045 0.065
b2
c 1.14 1.40 0.045 0.055
c2 8.64 9.65 0.340 0.380
D 9.65 10.54 0.380 0.415
e
e1 14.60 15.88 0.575 0.625
L 2.24 2.84 0.090 0.110
L1 1.02 2.92 0.040 0.112
L2 1.20 1.78 0.050 0.070
L3
Copyright ANPEC Electronics Corp. 14 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117 A a
Package Information c
SOT-223( Reference JEDEC Registration SOT-223)
D
B1
H E
L
e
e1 K
A1
b
B
Dim Millimeters Inches
Min. Max. Min. Max.
0.06 0.07
A 1.50 1.80
A1 0.02 0.08
B 0.60 0.80 0.02 0.03
0.11 0.12
B1 2.90 3.10 0.01 0.01
0.25 0.26
c 0.28 0.32 0.13 0.15
D 6.30 6.70 0.26 0.29
0.04 0.04
E 3.30 3.70 0.06 0.08
10
e 2.3 BSC 0 0.09 BSC
0.18 BSC
e1 4.6 BSC
13
H 6.70 7.30
L 0.91 1.10
K 1.50 2.00
0 10
13
Copyright ANPEC Electronics Corp. 15 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Physical Specifications
Terminal Material Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb
Lead Solderability Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
Packaging 2500 devices per reel
Reflow Condition (IR/Convection or VPR Reflow)
Reference JEDEC Standard J-STD-020A APRIL 1999
temperature Peak temperature
183C
Pre-heat temperature
Time
Classification Reflow Profiles
Average ramp-up rate(183 C to Peak) Convection or IR/ VPR
Preheat temperature 125 25 C) Convection 10 C /second max.
Temperature maintained above 183 C
Time within 5 C of actual peak temperature 3C/second max. 60 seconds
Peak temperature range 120 seconds max. 215~ 219 C or 235 +5/-0 C
60 ~ 150 seconds 10 C /second max.
Ramp-down rate 10 ~ 20 seconds
Time 25 C to peak temperature 220 +5/-0 C or 235 +5/-0 C
6C /second max.
6 minutes max.
Package Reflow Conditions
pkg. thickness 2.5mm pkg. thickness < 2.5mm and pkg. thickness < 2.5mm and pkg.
and all bags pkg. volume 350 mm volume <
Convection 220 +5/-0C
VPR 215-219 C Convection 235 +5/-0 C
IR/Convection 220 +5/-0 C VPR 235 +5/-0 C
IR/Convection 235 +5/-0 C
Copyright ANPEC Electronics Corp. 16 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Reliability test program
Test item Method Description
SOLDERABILITY MIL-STD-883D-2003
HOLT MIL-STD-883D-1005.7 245C , 5 SEC
PCT JESD-22-B, A102 1000 Hrs Bias @ 125 C
TST MIL-STD-883D-1011.9 168 Hrs, 100 % RH , 121C
ESD MIL-STD-883D-3015.7 -65C ~ 150C, 200 Cycles
Latch-Up JESD 78 VHBM > 2KV, VMM > 200V
10ms , Itr > 100mA
Carrier Tape & Reel Dimension
t
Po P D
E
P1
F Bo
W
Ao D1 Ko
T2
J
C
A B
T1
A p p lic a tion A B C J T1 T2 W P E
TO -252 330 3 100 2 13 0. 5 2 0 .5 1 6.4 + 0 .3 2 .5 0 .5 1 6+ 0.3 8 0 .1 1.75 0.1
F D D1 Po -0 .2 Ao - 0 .1 Ko t
P1 Bo
7 .5 0 .1 1 .5 + 0.1 1 .5 0 .25 4 .0 0 .1 2 .0 0 .1 6 .8 0 .1 1 0 .4 0 .1 2 .5 0 .1 0 .3 0 .05
B C J T1
A p p lic a tion A T2 W P E
80 2 13 0. 5 2 0 .5 24 4 2 0 .3 2 4 + 0.3
3803 D D1 Po P1 1 6 0 .1 1 .7 5 0 .1
- 0 .1
1 .5 + 0.1
TO -263 F B Ao Bo Ko t
5 .2 0 .1 0 .3 5 0 .0 1
11 .5 0 .1 6 2 1 .5 1 .5 0 .25 4 .0 0 .1 2 .0 0 .1 1 0 .8 0 .1 1 6 .1 0 .1
D C J P 3
A p p lic a tion A T1 T2 W E
1 2 .7 5 2 0 .6
3301 0 .1 5 Po 1 2.4 + 0.2 2 0 .2 1 2 0 .3 8 0 .1 1 .7 5 0 .1
D1
S O T-223 F P1 Ao Bo Ko t
5 .5 0 .0 5 1 .5 + 0 .1 1 .5 + 0 .1 4 .0 0 .1 2 .0 0 .0 5 6 .9 0 .1 7 .5 0 .1 2 .1 0 .1 0 .3 0 .0 5
Copyright ANPEC Electronics Corp. 17 www.anpec.com.tw
Rev. B.8 - Jun., 2003
APL1117
Cover Tape Dimensions
Application Carrier Width Cover Tape Width Devices Per Reel
TO- 252 16 13.3 2500
TO- 263 24 21.3 1000
SOT- 223 12 9.3 2500
Customer Service
Anpec Electronics Corp.
Head Office :
5F, No. 2 Li-Hsin Road, SBIP,
Hsin-Chu, Taiwan, R.O.C.
Tel : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
7F, No. 137, Lane 235, Pac Chiao Rd.,
Hsin Tien City, Taipei Hsien, Taiwan, R. O. C.
Tel : 886-2-89191368
Fax : 886-2-89191369
Copyright ANPEC Electronics Corp. 18 www.anpec.com.tw
Rev. B.8 - Jun., 2003
This datasheet has been downloaded from:
www.EEworld.com.cn
Free Download
Daily Updated Database
100% Free Datasheet Search Site
100% Free IC Replacement Search Site
Convenient Electronic Dictionary
Fast Search System
www.EEworld.com.cn
All Datasheets Cannot Be Modified Without Permission
Copyright Each Manufacturing Company