EEWorld咨询电话：82357002，82350740－8068 邮件咨询：datasheet@eeworld.com.cn
器件描述：100kHz 1.25A Switching Regulators
器件厂商：MICREL [Micrel Semiconductor]
厂商主页：http://www.micrel.com/
文件大小：158.17KB
文件页数：17
PDF阅读：MIC2172BN.pdf (点击阅读器件资料)
摘要：
April 2005 1 M9999-042205
MIC2172/3172 Micrel, Inc.
slave’s. The master MIC2172’s oscillator frequency is in-
creased up to 135kHz by connecting a resistor from SYNC to
ground (see applications information).
The MIC2172/3172 is available in an 8-pin plastic DIP or
SOIC for –40°C to +85°C operation.
Features
?1.25A, 65V internal switch rating
? 3V to 40V input voltage range
? Current-mode operation
?Internal cycle-by-cycle current limit
? Thermal shutdown
? Low external parts count
? Operates in most switching topologies
? 7mA quiescent current (operating)
?<1?A quiescent current, shutdown mode (MIC3172)
? TTL shutdown compatibility (MIC3172)
? External frequency synchronization (MIC2172)
? External frequency trim (MIC2172)
?Fits most LT1172 sockets (see applications info)
Applications
? Laptop/palmtop computers
? Toys
? Hand-held instruments
?Off-line converter up to 50W
(requires external power switch)
?Predriver for higher power capability
? Master/slave configurations (MIC2172)
General Description
The MIC2172 and MIC3172 are complete 100kHz SMPS
current-mode controllers with internal 65V 1.25A power
switches. The MIC2172 features external frequency syn-
chronization or frequency adjustment, while the MIC3172
features an enable/shutdown control input.
Although primarily intended for voltage step-up applications,
the floating switch architecture of the MIC2172/3172 makes
it practical for step-down, inverting, and Cuk configurations
as well as isolated topologies.
Operating from 3V to 40V, the MIC2172/3172 draws only
7mA of quiescent current making it attractive for battery
operated supplies.
The MIC3172 is for applications that require on/off control of
the regulator. The MIC3172 is externally shutdown by
applying a TTL low signal to EN (enable). When disabled, the
MIC3172 draws only leakage current (typically less than
1?A). EN must be high for normal operation. For applications
not requiring control, EN must be tied to V
IN
or TTL high.
The MIC2172 is for applications requiring two or more SMPS
regulators that operate from the same input supply. The
MIC2172 features a SYNC input which allows locking of its
internal oscillator to an external reference. This makes it
possible to avoid the audible beat frequencies that result from
the unequal oscillator frequencies of independent SMPS
regulators.
A reference signal can be supplied by one MIC2172 desig-
nated as a master. To insure locking of the slave’s oscillators,
the reference oscillator frequency must be higher than the
MIC2172/3172
100kHz 1.25A Switching Regulators
Typical Applications
C4
470?F
D2
1N5818
C1
22?F
C2
1?F
R3
1k
R4*
V
OUT
5V, 0.25A
* Optional voltage clipper (may be req’d if T1 leakage inductance too high)
C3*
D1*
R1
3.74k
1%
R2
1.24k
1%
V
IN
4V to 6V
T1
Enable
Shutdown
1:1.25
L
PRI
= 100?H
MIC3172
V
IN
V
SW
FB
EN
GND
P1 P2 S
COMP
Figure 2.
MIC3172 5V Flyback Converter
+5V
(4.75V min.)
D1
1N5822
MIC2172
V
IN
V
SW
FB
C1*
22?F
R3
1k
C3
1?F
R1
10.7k
1%
C2
470?F
V
OUT
+12V, 0.14A
L1
27?H
* Locate near MIC2172 when supply leads > 2"
R2
1.24k
1%
SYNC
GND
P1 P2 S
N/C
COMP
Figure 1.
MIC2172 5V to 12V Boost Converter
Micrel, Inc. ? 2180 Fortune Drive ? San Jose, CA 95131 ? USA ? tel + 1 (408) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com
相关器件：MIC2172 MIC2172YM MIC2172_05 MIC2172BM MIC2172YN MIC3172YM MIC3172BM MIC3172BN MIC3172YN
|
