Product Qualification Report
IPLK70R600P7
CoolMOS
TM
Description
This product qualification report describes the characteristics of the product with respect to quality and reliability.
The qualification sample selection was done on production lots which were manufactured and tested on standard
production processes and meet the defined requirements.
The qualification test results of those products as outlined in this document are based on
JEDEC
for target
applications and may reference existing qualification results of similar products. Such referencing is justified by the
structural similarity of the products.
Qualification Assessment
Fully qualified according to
JEDEC
for
Industrial Applications
and assessed as PASS
For further information about comparable products, please contact the nearest Infineon Technologies office
(www.infineon.com).
www.infineon.com
Please read the Important Notice and Warnings at the end of this document
Revision 1.0
IPLK70R600P7
PG-TDSON-8
MSL: 1; 260°C
Electrical Stress Test Results:
Test Description
Parametric Verification
High Temperature Reverse Bias
JESD22 A108
High Temperature Gate Bias
JESD22 A108
High Humidity High Temp.
Reverse Bias
JESD22 A101
Intermitted Operational Life Test
MIL-STD 750 / Meth.1037
ESD (HBM)
JESD22-A114
ESD (CDM)
JESD22-C101
qualified 2018
Abbr.
PV
HTRB*
HTGB*
H3TRB*
Condition
-55°C, +25°C, +150°C
Ta ≥ 150°C
V
DS
≥ 80% BVDSS
Ta = 150°C
V
GS
= +/-20V
Ta = 85°C
rh = 85%
V
DS
= 100V
Delta T =100K
Class 2
2000V to < 4000V
Class C3
≥ 1000V
Duration
1000 h
1000 h
1000 h
Lots/SS
3 x 25
3 x 77
3 x 77
3 x 77
Fail/Qty
0 / 75
0 / 231
0 / 231
0 / 231
Result
PASS
PASS
PASS
PASS
IOL*
HBM
CDM
15000 cyc
3 x 77
0 / 231
PASS
PASS
PASS
Environmental Stress Test Results:
Test Description
Pre-conditioning
J-STD020 / JESD22 A113
Temperature Cycling
JESD22 A104
Unbiased Highly Accelerated
Stress Test
JESD22 A118
Wave solder simulation
for SMD devices
JESD22 A111
Abbr.
PC
TC*
UHAST*
Condition
MSL and 3 x reflow
-55°C to +150°C
Ta = 130°C
rh = 85%
T=260°C / 1 x 10sec and
Temperature Cycling
-55°C to +150°C; 100 cyc.
Duration
Lots/SS
3 x 77
Fail/Qty
0 / 231
0 / 231
0 / 231
Result
PASS
PASS
PASS
1000 cyc
96 h
3 x 77
3 x 77
WS*
3 x 25
0 / 75
PASS
Mechanical Stress Test Results:
Test Description
Destructive Physical Analysis
Abbr.
DPA
Condition
samples from UHAST &
TC
Duration
Lots
3
Fail/Qty
0/3
Result
PASS
Notes:
* For SMD devices reliability stress tests performed after preconditioning test (PC) according to JESD22
Revision 1.0
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
Edition 2016-01-22
Published by
Infineon Technologies AG
n.a.owners.
81726 München, Germany
© 2018 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about this
document?
Email:
erratum@infineon.com
Document reference
n.a.
IMPORTANT NOTICE
The information given in this document shall in no
event be regarded as a guarantee of conditions or
characteristics (“Beschaffenheitsgarantie”).
With respect to any examples, hints or any typical
values stated herein and/or any information
regarding the application of the product, Infineon
Technologies hereby disclaims any and all
warranties and liabilities of any kind, including
without limitation warranties of non-infringement
of intellectual property rights of any third party.
In addition, any information given in this document
is subject to customer’s compliance with its
obligations stated in this document and any
applicable legal requirements, norms and
standards concerning customer’s products and any
use of the product of Infineon Technologies in
customer’s applications.
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer’s technical departments
to evaluate the suitability of the product for the
intended application and the completeness of the
product information given in this document with
respect to such application.
For further information on the product, technology,
delivery terms and conditions and prices please
contact your nearest Infineon Technologies office
(www.infineon.com).
WARNINGS
Due to technical requirements products may
contain dangerous substances. For information on
the types in question please contact your nearest
Infineon Technologies office.
Except as otherwise explicitly approved by Infineon
Technologies in a written document signed by
authorized
representatives
of
Infineon
Technologies, Infineon Technologies’ products may
not be used in any applications where a failure of
the product or any consequences of the use thereof
can reasonably be expected to result in personal
injury.
京公网安备 11010802033920号
Copyright © 2005-2023 EEWORLD.com.cn, Inc. All rights reserved
电子工程世界
